The EP Series Helical Bevel Reducer provides unmatched performance, durability, and design flexibility. This unit offers torque capacities up to 20,000 Nm (14,750 ft pounds).
The cat4CAD software allows simple interactive product collection of the entire gearbox and gear-electric motor system. Cat4CAD facilitates you in selecting and configuring these products, provides you the opportunity to print out considerable technical data linens, and generates complete 2D drawings and 3D versions for direct download.
11 sizes
Insight power capacities from 0.16 to 120 HP
Gear ratios from 5:1 to 8900:1
Torque capacities to 20,000 Nm
Inverter duty course F insulated motor windings
Course 12 Helical and Spiral Bevel Gears: Provides higher efficiencies and greater torques in smaller sizes.
Multiple Input Options: Integral gear motors, ” or metric shafts, NEMA, IEC, and servo adapters provide unmatched drive versatility.
Multiple Output Choices: Hollow bores and shrink disks for shaft installation, inch and metric output shafts, installation pilots and flanges provide a wide selection of design solutions.
UNIBLOCK Housing: For optimum rigidity, universal installation on five sides or with a torque arm.
Worldwide Motor: Multiple leads and windings for worldwide multi volt/Hz requirements in addition modular design to accept brakes, encoders or forced cooling.
High efficiency electric motor design available
Innovative self-locking, self-aligning taper shaft motor connection
Gearbox supplied factory filled up with synthetic oil
Corrosion and shock resistant cast iron housing
High efficiency helical-bevel gears. 98% per stage
Normally closed breather with multiple locations (Optional OtN2000)
Double lip seals upon heat treated, plunge ground shafts
Shaft mounting choices include tapered bushings designs
This is a thorough offering of energy-efficient, right angle helical bevel enclosed gearing. It really is available as gearmotors and a number of reducers with torque capacities up to 119,000 inch pounds. Housing designs include footed, encounter and flanged configurations. Gearmotors are available in three phase high efficiency designs through 50 HP and single phase to 5 HP. We offer a selection of input and result shaft options. Additionally, you will find fixed and variable velocity motors and selection of ratios obtainable in this product offering.
Features
Accommodates input power from ¼ Hp to 75Hp
Torque ratings up to 119,489 in-lbs
Decrease ratios up to 7,500:1
Helical – bevel – helical gear train offers affordable high and low speed solutions
Up to 94% efficient
Four input options available for all units
Two output flange choices – B5 and B14
Multiple output shaft interfaces
Crucial dimensions interchangeable with main competitors
Modifications / Accessories
Integral Gearmotor
Clamp Collar C-Face Input
Solid Shaft Input
3-Piece Coupled C-Face Input
CEMA Screw Conveyor Adapter
EZ Kleen Washdown Package
XT Output Seals
Backstop
DURABLE Output Bearings
Inch or Metric Dimensions
Common Applications
Troughing Belt Conveyors
Slider Bed Conveyors
Mixer Drives
Screw Conveyors
Bucket Elevators
General Industrial Machinery
Common Industries
Aggregate and Cement
Air Handling
Chemical, Oil, and Gas
Food, Beverage, and Pharmaceutical
Paper and Forest
Unit and Baggage Handling
Water and Wastewater
As per the developing and varying needs of customers, you can expect a wide variety of Helical Bevel Equipment Reducers. The technological articles of our products allows for an extraordinary efficiency/lifespan ratio. The extremely versatile Helical Bevel Gear Reducers we provide are successfully found in a multitude of commercial and civil applications. These are B-Series units that offer excellent value for money and output torque/weight ratio, especially due to the fact they need not a lot of servicing. Besides these, our products are available in cast iron (sizes 063 to 163) or light weight aluminum (sizes A42 to A73) casing.
Features:
Sizes: 060-080-100-125-140-150-160
Available versions: B-fitted for electric motor coupling, IB with input shaft, CB with compact motor, PB-fitted for motor coupling with flexible joint
Casing with foot FC, flange SC and general UC
Switch on to 90 kW
Gears hardened and tempered with shaved or floor profile
Gearing with 3 reduction stages
Gleason spiral bevel gear pairs with run-in profile, mounted as second decrease stage for a higher resistance
Reduction ratios between 5, 71 and 187, 24
Torque max 13.000 Nm and admissible radial loads max 80.000 N
High-strength casings optimized with FEM analysis and input and result flanges of grey cast-iron G200 to make sure top level performances and high reliability
Load capacity calculated and verified according to ISO 6336 and AGMA 2001
Painted with RAL 5010 blue epoxy-polyester powder
Accessories: torque arm, result flange, result shaft, shrink disk, backstop device, protection cover package, viton oil seals, reinforced output, assemble/disassemble kit
Series EP right angle helical bevel gear motors offer ratios from 8:1 to 160:1 in three phases or up to 10000:1 in five phases. Motors can be found up to 90kW and output torque capability up to 12,300 Nm.
The series EP helical bevel gear motor was created with integral cast feet for base or end mounting and may be helical bevel gear reducer offered with single or double extended output shafts.
Devices are also available as shaft mounted or with result flanges and are available for installation horizontally or vertically. The units can also be offered with a bolt on torque response bracket and all variants can be found possibly motorised or with an input shaft assembly.
Adding to the new range of Ever-Power helical gear motors this product takes benefit of our a long time of accumulated design knowledge together with the use of high quality materials and elements. The end result is a series of velocity reducing geared motors offering high load transporting capacities, increased efficiency, quiet running and reliability.
Top features of Helical Bevel Gear Motor
Standard motor connection
Ability to fit double oil seals, on input and output shaft because required.
All models are dimensionally interchangeable with other major manufacturers.
Units are manufactured and assembled from a family group of modular kits for distributor friendliness minimizing inventory and maximizing availability.
Motorized units can be fitted with a backstop module and reducer Systems can be installed with a backstop and fan.
Applications:
-Conveyors, Agitators, Elevators, Cranes, Crushers
-Helical Bevel gear motors are used in industries such as chemical substances, pharma, packaging, food processing, plastic-type material and automation etc.
Key Features:
Sizes: A40-A50-A70
Available versions: EP – fitted for electric motor coupling, IEP – with input shaft, CEP – with compact motor
Cases with foot, flange or universal
Switch on to 4,8 Kw
Gears with shaved or floor profile
Gearing with 2 and 3 reduction stages
Hypoid bevel gears for size A40 and A50, gleason bevel gear pairs for size A70, all with run-in profile
Reduction ratios between 7,62 and 442,76
Torque max 450 Nm and admissible radial loads max 5.500 N on hollow shaft and 10.000 N on solid shaft
Cases in die-cast aluminium alloy
Excellent mechanical strength while being and particularly lightweight
Load capacity calculated to ISO6336 and verified according to AGMA 2001-B88
Painted with RAL 5010 blue epoxy-polyester powder in according to DIN 1843
Accessories: torque arm, output flange, output shaft.
Generallntroduction of HK series:
Gear Reducer
The EP series gear units, are novel transmission device and composed of Y series electric motor, helical gear,Arc gear and worm gear. The gears are made of high wear-resisting alloy components, specifically and finely processed.
Advantages:
1: Helical-bevel equipment two-stage reducer
2: Compact framework, high efficiency
3: Quenched 20CrMnTi for gears
4: CE, ISO9001.
5: Compact design, small volume, good appearance ,and solid capacity to be overloaded.
6: Precise division and wide range for transmission ratio.
7: The efficiency is up to since high because 96% with low energy intake, strong adaptability and is capable of operating continually in corrosive or damp environment.
8: All- purpose make use of, convenient and low-price maintenance.
9: New seal gadget, strong adaptability.
10: Varied range of motor combinations, mouting positions and struture projects.